Showing results: 181 - 195 of 346 items found.
-
SUBT-3.0 -
Dynamic Load Monitoring Ltd.
The Subsea Tensile Link is specially designed for working in subsea conditions and is used for measuring tensile loads. With an optional integral 4-20mA amplifier the load cell is packaged in a wooden case with a subsea rated signal cable to customer specific lengths or alternatively can be supplied with a TW-3.0-S display. Fully sealed with a subsea connector and pressure tested to over 250Bar the load cell is the ideal instrument for easily and accurately measuring subsea loads.
-
SLM -
Integrated Test + Measurement
Since 2001 ITM has installed structural strain based monitoring systems in the pulp & paper and energy generation industries. For these systems, our engineers and field service technicians turn structures into measurement instruments (load cells). Load outputs from the structural load cells are monitored and published by a realtime controller to its local interface or network historians and HMIs.
-
SY031 -
Synectic Electronics
SY031 Portable Digital Load Meter is a handheld battery powered instrument. The 4.5 digit 24 bit instrument displays measurements from load cells, torque transducers and other strain gauge bridge transducers. The meter offers peak and trough hold and up to 16 channels of stored (load cells or other sensor) calibration data, stored in non-volatile memory.
-
Jinan Testing Equipment IE Corporation
TE electronic calibration module provides an easy way to calibrate load cell or extensometer and signal conditioning electronics without using a mechanical calibrator. It enables performing on-site electrical calibration and easy to periodically “spot check”, which will help ensure that the load cell and the extensometer and electronics are calibrated correctly.
-
Element 1 Power Systems Inc.
E1PS is glad to bring you a low cost method to test fuel cells and produce professional test data results for under $1,000.00, fuel cell included! The Fuel Cell Test Station comes complete with everything but the hydrogen. There are three meters*, a load box, forced air housing and a fuel cell.
-
JFE Advantech Co., Ltd.
This weigher can be easily installed in a hopper for faster construction by adopting our prominent load cells with built-in constrainer.
-
Interface Inc.
Multi Axis Load Cell are designed and manufactured by Interface to measure a multiple of forces and/or moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the other forces or moments - when installed and used according to specifications.
-
JB104SS -
Interface Inc.
The JB104SS junction box model is designed to connect and trim up to four load cells per board. It may also be used in combination with additional juction boxes through the use dof an expansion port on the main board to connect multiple junction boxes thus allowing the summing of more than four load cells.
-
Laurel Electronics, Inc
Equipped with a DC or load cell signal conditioner, this Laureate offers special firmware for scale / weighing applications: two tare functions; count by 1, 2, 5, 10, 20, 50 or 100; auto-zero function; setpoint offset, and dummy right-hand zero for display to 999,990. Built-in excitation for up to four 350-ohm load cells in parallel.
-
WonATech Co.,Ltd
For 100Watt DMFC single cell testCompact sizeConsists of electronic load, gas/liquid controller, humidifier and methanol pump etc.
-
LKVE/i -
Gigasense
The PIAB LKVE electronic overload protection system consists of a force transmitter with amplifier and an electronic signal processing unit. The PIAB LKVE force transmitter is attached to a stationary line part. The rope is deflected via a slight angle between the two wheels and the clamping jaw. When loaded, the rope tends to straighten and applies a force which is transmitted to the load cell. The load cell in the PIAB LKVE delivers a signal proportional to the force on the load cell. The signal is amplified and is converted to 4-20mA. This standardized signal (4-20mA) allows distances between the force transmitter and the electronic unit to be 500 m.
-
Sciencetech, Inc.
The SSIVT is an electrical current-voltage measurement system used to characterize photovoltaic cell performance. This current-voltage tester works by sampling various current versus voltage combinations of the photovoltaic cell with a variable impedence load. The performance of the photovoltaic cell is determined by measuring this output I-V relationship while it is being illuminated.
-
HS 2000 -
Jinan Testing Equipment IE Corporation
The load cell calibrator is used to calibrate the load of testing machine and hardness tester, and also can be used for force measuring. It is digital display type with high accuracy of less than +0.3%, and easy to operate
-
SY091 -
Synectic Electronics
SY091 is a Rugged 24 bit portable strain gauge indicator, which can indicate the load present on one or two attached cells. Display measurements from plug in sensors. The sensors can be load cells LVDTs or pressure sensors. 2.4Ghz wireless connectivity is also an option. The unit has a 10.75mm 8 character (+/- 5 digit measurement) LCD display.
-
Synectic Electronics
The SY008 VI Load Cell Sensor Signal Conditioner IP66 converts 0-5V dc in to 4-20mA out. The SY008 can either provide a 5V or 10V source to a variety of transducers; load cells, RVDTs, potentiometers (precision linear transducer), tilt sensors and contactless position sensors. Almost any sensor that produces an output signal voltage in the range 0-5V dc.